Hardware & Plumbing
Homebrewing plumbing and hardware equipment for any homemade beer setup. You can choose from our wide variety of plumbing equipment and hardware.
Showing all 50 results
-
Brew Pump With Stainless Steel Head 120 VAC
Max flow rate; 5 gal/minute at zero head 304SS head with 1/2" male NPT inlet and output 120 volt AC motor with included cord and plug Sealed motor housing is water/splash resistant (not water proof)#MP295 -
Center pickup – 3/8″ O.D. Tube
Dip tube Size: 9" Long - 4" Bend ,3/8" O.D Compression Fitting: 3/8MPT X1/2"FPT#SST021-38 -
Diptube Center Pickup – 1/2″ O.D. Tube
Dip tube Size: 9" Long - 4" Bend,3/8" O.D Compression Fitting: 1/2MPT X1/2"FPT#SST022-12 -
Economy Brewing Pump With Stainless Steel Head 220V AC
This pump wins for the least expensive stainless headed magnetic drive pump for the budget conscious brewer. The overall size is smaller than the Chugger, March, and Blichmann Riptide and the flow rate is relatively diminished in comparison as...#MP296 -
SS 304 Flange Nut
1/2"NPS Locknut with flat flange, made from stainless steel 304.#SSLN161 -
Stainless Adapter 1/2 in. FPT x 1/2 in. MPT
Stainless Adapter 1/2 in. FPT x 1/2 in. MPT#SSA379 -
Stainless Ball Valve 1/2 in. Full Port
304 Stainless steel, full port, two piece ball valves that will last for years. Easy to clean with 1/2" FPT on input and output High grade 304-stainless made to last with1000psi rating#2BV026 -
Stainless Elbow Barb 3/8 in. x 1/2 in. MPT
This heavy duty Stainless Elbow with barb is a versatile piece of hardware for your brewing setup. The 1/2" MPT threaded end attaches to a 1/2" threaded FPT fitting. The barb will accommodate 1/2" ID tubing. Use it anywhere you want tubing...#SS277 -
Stainless Hex Nipple – 1/2 inch x 1 ininch Threaded
1/2″ Stainless Steel Nipple. An excellent upgrade to a standard nipple#SSHN010 -
Stainless Nipple _ 1/2″ x 1″ Threaded
1/2" MPT, fully threaded the entire length. 1" long.This 1/2" Male Pipe Thread Male to Male connector allows you to attach any 1/2" Female Pipe Thread item that we carry for your vari-ous homebrewing project needs.#SSN012-S -
Stainless Steel 1/2 in. High Flow Elbow Barb
The barb ID is 5/8″ and the OD is 3/4″. Our 1/2″ ID silicone tubing will just barely stretch over the barb so it’s a nice snug fit.#SSHF003 -
Stainless Steel Ball Valve – 1/2 in. (3 – Piece)
Heavy duty ball-valve that can be taken apart for easy cleaning. 1/2″ female pipe thread inlet and outlet. Made from 304-type stainless steel.#3BV025 -
Stainless Steel Fittings 1/2in. FPT x 1/4 in. barb
Stainless Steel Fittings 1/2in. FPT × 1/4 in. barb Use this fitting for connecting tubing directly to your pump. 1/2″ FPT on one side, with a 1/2″ barb on the other. If you are not using a QD Set or a ball valve, this is a handy piece of...#FID012 -
Stainless Steel Fittings 1/2 in. FPT x 1/4 in. Barb
Stainless Steel Fittings _ 1/2 in. FPT x 1/4 in. Barb#SSF306 -
Stainless Steel Fittings 1/2 in. FPT x 1/2 in. Barb
1/2 in. MPT x 1/2 in. Barb. For Insertion into a ball valve for connecting 1/2″ ID line. Made from 304 type stainless steel.#SSFM1212 -
Stainless Steel Fittings 1/2 in. FPT x 3/8 in. Barb
Stainless Steel Fittings 1/2 in. FPT x 3/8 in. Barb#SSF309 -
Stainless Steel Fittings 1/2 in. MPT x 3/8 in. barb
Stainless Steel Fittings 1/2 in. MPT x 3/8 in. barb#SSB007-10 -
Stainless Steel Fittings 1/2in. MPT x 1/4 in. barb
Stainless Steel Fittings 1/2in. MPT x 1/4 in. barb#SSM302 -
Stainless Steel Fittings 1/2in. MPT x 5/8 in. barb
Stainless Steel Fittings 1/2in. MPT x 5/8 in. barb#SSB009-15 -
Stainless Steel Fittings 1/4in. MPT x 1/4 in. barb
Stainless Steel Fittings 1/4in. MPT x 1/4 in. barb#SSM303 -
Stainless Steel Fittings 3/4 in. FPT x 3/4 in. Barb
3/4 in. NPT x 3/4 in. Barb Wort Chiller Water out/in fittings#SSFM3434 -
Stainless Steel Fittings 3/8 in. FPT x 1/4 in. Barb
Stainless Steel Fittings 3/8 in. FPT x 1/4 in. Barb#SSF307 -
Stainless Steel Fittings 3/8 in. FPT x 3/8 in. Barb
Stainless Steel Fittings 3/8 in. FPT x 3/8 in. Barb#SSF308 -
Stainless Steel Fittings 3/8in. MPT x 1/2 in. barb
Stainless Steel Fittings 3/8in. MPT x 1/2 in. barb#SSM304 -
Stainless Steel Fittings 3/8in. MPT x 1/4 in. barb
Stainless Steel Fittings 3/8in. MPT x 1/4 in. barb#SSM305 -
Stainless Steel Flat Washer – For 1/2″ NPT, Bulkheads
Thick: 1/8″ nominal thickness (closer to .11″ actual), .825″ inside diameter. 1.32″ outside diameter.#SSW001 -
Stainless Steel Nipple – 1/2 in. x 1.5 in. (Length)
Stainless – Nipple – 1/2 in. x 1.5 in. A stainless steel nipple used to combine two fittings with 1/2″ FPT threads. There is a 1/2” space between threads.#SSN011-L -
Stainless Steel Quick Disconnect – Female QD x 1/2 in. Barb
Quickly and effortlessly switch lines between fittings with this stainless steel quick disconnect. Move tubing from one kettle to another Easily switch lines between pumps, chillers, hoprockets or other in-line equipment Stainless steel...#SQD177 -
Stainless Steel Quick Disconnect – Female QD x 1/2 in. FPT
Quickly and effortlessly switch lines between fittings with this stainless steel quick disconnect. Move tubing from one kettle to another Easily switch lines between pumps, chillers, hoprockets or other in-line equipment Stainless steel...#SQD175 -
Stainless Steel Quick Disconnect – Female QD x 1/2 in. MPT
Quickly and effortlessly switch lines between fittings with this stainless steel quick disconnect. Move tubing from one kettle to another Easily switch lines between pumps, chillers, hoprockets or other in-line equipment Stainless steel...#SQD176 -
Stainless Steel Quick Disconnect – Male QD x 1/2 in. Barb
Quickly and effortlessly switch lines between fittings with this stainless steel quick disconnect. Move tubing from one kettle to another Easily switch lines between pumps, chillers, hoprockets or other in-line equipment Stainless steel...#SQD178 -
Stainless Steel Quick Disconnect – Male QD x 1/2 in. FPT
Quickly and effortlessly switch lines between fittings with this stainless steel quick disconnect. Move tubing from one kettle to another Easily switch lines between pumps, chillers, hoprockets or other in-line equipment Stainless steel...#SQD180 -
Stainless Steel Quick Disconnect – Male QD x 1/2 in. MPT
Quickly and effortlessly switch lines between fittings with this stainless steel quick disconnect. Move tubing from one kettle to another Easily switch lines between pumps, chillers, hoprockets or other in-line equipment Stainless steel...#SQD179 -
Stainless Steel Quick Disconnect – Male QD x 3/4 in. FPT
Quickly and effortlessly switch lines between fittings with this stainless steel quick disconnect. Move tubing from one kettle to another Easily switch lines between pumps, chillers, hoprockets or other in-line equipment Stainless steel...#SQD276 -
Stainless Steel Quick Disconnect – Male QD x 3/8 in. Barb
Quickly and effortlessly switch lines between fittings with this stainless steel quick disconnect. Move tubing from one kettle to another Easily switch lines between pumps, chillers, hoprockets or other in-line equipment Stainless steel...#SQD174 -
Stainless Steel Quick Disconnect – Male QD x 1/2 in. Barb
Quickly and effortlessly switch lines between fittings with this stainless steel quick disconnect. Move tubing from one kettle to another Easily switch lines between pumps, chillers, hoprockets or other in-line equipment Stainless steel...#12 -
Stainless Steel Quick Disconnect – Male QD x 5/16 in. Barb
Quickly and effortlessly switch lines between fittings with this stainless steel quick disconnect. Move tubing from one kettle to another Easily switch lines between pumps, chillers, hoprockets or other in-line equipment Stainless steel...#SQD264 -
Stainless Steel Quick Disconnect – Replacement Gasket
Stainless Steel Quick Disconnect – Replacement Gasket#R265 -
Tube Compression X NPT Threaded Adaptor – 1/2″ Tube x 1/2″ MNPT
304-type stainless steel 1/2" NPT to 1/2" Compression fitting.#COMP019-1212 -
Tube Compression X NPT Threaded Adaptor – 3/8″ Tube x 1/2″ MNPT
Consistent gaugeability upon initial installation Easy to disconnect and retighten Wide variety of materials and configurations Demonstrated reliability and performance Double ferrule fitting reduces possibility of leakage#COMP019-1238 -
Type A – Male QD/ Female 1/2″ NPT
The most common use for this part is attaching to the wort in/out ports on a plate chiller. It can also be used for recirculation ports, the in/out of a HERMS coil. etc.#CQD018 -
Type B – Female QD Coupling to Male 1/2″ NPT
The most common use for this part is attaching to the wort in/out ports on a plate chiller. It can also be used for recirculation ports, the in/out of a HERMS coil. etc.#CQD016 -
Type B Big Flow – Camlock Quick Disconnects
Female Camlock Coupler x 21mm Hose Barb, Camlock Quick Connect#CQD017 -
Type C – Camlock Disconnect Female QD / 1/2″ Hose Barb
Female Camlock Coupler x 1/2″ Hose Barb, Camlock Quick Connect#CQD014 -
Type F – Camlock Fittings Male QD / Male 1/2″ NPT
Camlock Type "F" quick disconnect 1/2" NPT stainless steel fitting#CQD015 -
Weldless Bulkhead 304 Stainless Steel
Weldless Bulkhead easily and quickly add a valve or thermometer to your stock pot, kettle, bucket, mash ton, or later ton. This bulkhead includes two high temp Flat Gaskets One goes on the inside of the kettle to form a tight leak free seal, the...#C-WB034 -
Weldless Kettle Bulkhead 1/2 inch O-rings
Weldless Kettle Bulkhead 1/2 inch O-rings#ROR024 -
Mini Ball Valve 1/2″ MPT – 1/2″ FPT
This 1/2" 316 stainless steel mini ball valve is an excellent option when you are limited with the amount of space you have for draining your brew kettle. It will withstand high temperatures and has a blow out system for preventing liquid from...#MBV202
Showing all 50 results